Re: Cannot control Servo using "jsupm_servo" module
Guys i found the issue. "jsupm_servo" is setting incorrect time perios to PWM signal. Required is 20ms but it is seeting 7.9ms. GPIO...
View ArticleRe: Where is Pin 1 physically located on the Edison Hirose 70 pin header?
Maybe a stupid question: You labeled Pin 1 on the far bottom right. If I count the Pins I get 37 per side -> 37*2=74 in total instead of the 70 Pins from the documentation? The same applies in this...
View ArticleRe: Cannot control Servo using "jsupm_servo" module
As a workaround you can use the following code to control your servo: Code:var AIO_pin = 0;//setup access analog input Analog pin #0 (A0) i.e. output of potentiometer. Assuming values read is between 0...
View ArticleRe: No Bluetooth-Audiostreaming with DualBand WirelessN 7260 under Windows 8
C'mon, don't blame the operating sistem.I just changed my wireless card to the 7260 too and learned the hard way. The card that came with the laptop worked great (atheros), i could stream music from...
View ArticleRe: Multiple servo controlling issues on Edison Arduino board
Hi Rob, Thank you for your explanation! This is exactly the issue from a bit more scientific aspect . So this means the PWM ports for servo controlling on edition not working as they should be, caused...
View ArticleDE3815TYKHE BIOS UPDATE 36 to 41 fails
I tried the Bios update on two devices from version 36 with TY0041.BIO and with TYBYT10H.86A.0041.EB.EXE. After verify when it starts flushing the process fails.Any idea? best regardsKlaus
View ArticleWhich OS should I use on my NUC DN2820? :D
I need you guys to decide what OS I should run on my NUC, im using it as a HTPC for myself Tried Ubuntu and I love it, I love Windows to, but.... Help me
View ArticleClik here to view.
Intel Galileo Gen2 is unable to connect to the network
Hi All,My Intel Galileo Gen2 board is unabale to connect to the network.I refer to the Getting Started-Ethernet,but I'm unable to get its IP address. I try to do the command:ifconfig eth0 up,ifconfig...
View ArticleRe: Bios Update Intel DQ45CB Motherboard
Allan Still no luck. I cleared any passwords and BIOS states no passwords etc.I downloaded the .BIO file , burnt it to a dvd both like a CD and like a USB. Tried to update pulling the jumper etc for...
View ArticleRe: no response in serial console
You can see more in AlexT;s bloghttp://alextgalileo.altervista.org/blog/galileo-uart-and-arduino-serial-objects-mapping/Serial = USBSerial1 = pins 0 & 1 Serial2 = 3.5mm portrgb
View ArticleRe: Intel HELP!!!! update utility does not recognize hardware
Hi Mark, Any chance you guys can bring back the old website. This new utility is far from complete and sadly as you know I have waited some time for a resolution and it is unlikely you guys will solve...
View ArticleRe: autogen-native_5.12.bb, do_compile ,failed
Hi, atvreddy Thanks for your reply. Did you use meta-clanton_v0.7.5 or meta-clanton_v1.0.1 ? Last year I had successfully built the Galileo Linux image and cross compiler using the meta-clanton_v0.7.5...
View ArticleRe: autogen-native_5.12.bb, do_compile ,failed
hi shaka, I used meta-clanton_v1.0.1 and followed the link ,which I mentioned in previous reply. that's fine, what about the issue ,is it solved or not ?
View ArticleRe: autogen-native_5.12.bb, do_compile ,failed
My machine is very slow and may need several hours to build. I'm waiting for the result... Thanks.
View ArticleIntel i7 chipset problematic with Windows 8.1
I had an issue with Windows 8.1 committing suicide and I had to reload Windows 8 and then upgrade to 8.1. Now Bluetooth doesn't work and fingerprint sensor doesn't work on i7 HP Pavilion dv7-6b32us. I...
View ArticleRe: How best proceed with overheating i7-4790K?
Get real temp or hw monitor (this one monitors a lot more things) to watch the temps and intel burn test to stress your cpu; if you get temps above 75 celsius then use xtu to read and tweak your cpu...
View ArticleClik here to view.
Re: No video signal on my NUC D54250WYKH
Thanks Kevin. I have a mini-HDMI to HDMI cable on order now so I can try it with my HDMI monitor. Fingers crossed. Robert.
View ArticleRe: Overscan issue
Bump. One month later and still no answer from Intel. Will this ever be addressed for people with n2820 NUCs?
View ArticleRe: How best proceed with overheating i7-4790K?
How many sticks of RAM do you have? Make sure you read your motherboard's manual on which slots to put the RAM in. If you don't put them by manufacturer's suggestions, your RAM will not run...
View Article